DIN 976 / DIN 975 threaded rods made to order
Made-to-order production range
| Diameters | M4 - M80 |
|---|---|
| Lengths | 20 mm - 6000 mm |
| Classes / materials | 4.8, 8.8, 10.9, 12.9 A2 (1.4301), A4 (1.4401) 25CrMo4+QT (1.7218) 21CrMoV5-7+QT (1.7709) 42CrMo4+QT (1.7225) X19CrMoNbVN11-1+QT (1.4913) X22CrMoV12-1+QT (1.4923) X6NiCrTiMoVB25-15-2+QT (1.4980) |
| Coatings | Hot-dip galvanized (HDG, tZn) Zinc plated (Zn) Plain (uncoated) |
| Thread types | Metric (standard) Left-hand Imperial (UNC, UNF, BSW) Trapezoidal |
| Standards | DIN 976-1, DIN 975, EN 1515-1 Annex A, BS 4882 |
| End forms | DIN 976-1 form A (plain ends) DIN 976-1 form B (chamfered ends) Machined ends to drawing |
| Certificates & compliance | EN 10204 3.1 / 3.2, PED 2014/68/EU, EN 10269 |
European manufacturer of specialist fasteners. Industry expertise since 1971
DIN 976 threaded rods and threaded bar (studding) manufactured to your specification - in the diameter, length, strength class, material and coating your project requires, with machined ends and material certificates for every batch.
Send an inquiry if your project needs rods outside stock sizes - large diameters, long lengths, special steels or machined ends. Rods are manufactured in Poland and delivered to customers across Europe, including Central and Eastern Europe.
Threaded rod manufacturer - see how our DIN 976 rods are made
A short film from our production: from the steel bar to finished threaded rods, ready for delivery to projects across Europe.
Threaded rods, threaded bar and studding cut to the finished length
A rod cut and machined on site is an extra operation, wasted material and a risk of damaging the thread - which means higher installation cost and longer crew time. We deliver rods ready to install: cut to length, with the ends machined to your documentation.
Cut to finished length
Every rod is produced to the length stated in the specification - no stock lengths to cut down on site.
Machined ends
Chamfers, undercuts and end machining done in production, according to the drawing.
Thread and coating intact
No on-site cutting means no damaged thread start and no uncoated cut ends.
Supplied with nuts and washers
Rods delivered together with matching nuts and washers.
Effect: Rods ready to install - no cutting, no material loss and no extra machining on the client's side.
Large diameter and long threaded rods: M4 to M80, up to 6000 mm
Large diameters and long lengths are where standard supply ends. We manufacture DIN 976 threaded rods across the full range - from small diameters to M80 - and in lengths up to 6000 mm - the upper limit of our production capabilities.
Diameters
M4 to M80 - including large diameter threaded rods M27, M30, M36, M42, M48, M56, M64 and M80 for heavy anchoring and load-bearing connections - for example an M24 threaded rod or an M30 threaded rod for foundation anchor bolts. The diameter is the thread size: an 8 mm threaded rod is M8, a 12 mm rod is M12 - in the UK often ordered as M8 studding or M12 studding.
Lengths
Standard lengths of 1000, 2000 and 3000 mm, or cut to the exact length of your project - long threaded rods and long threaded bar up to 6000 mm, with chamfered ends.
Threads
Metric right-hand and left-hand threads, imperial threads (UNC, UNF, BSW) and trapezoidal threads.
Standard
DIN 976-1 - the current standard for fully threaded rods, which replaced DIN 975.
Effect: One manufacturer for the whole size range - from M4 to M80, up to 6000 mm.
Custom threaded rods machined to your drawing
When a rod has to fit a specific connection, the thread alone is not enough. We produce threaded rods to drawing and modify them in our own machining shop.
Cutting and chamfering
Cutting to any length and chamfering of the ends.
Undercuts and turning
Undercuts and turning of the rod ends according to the documentation.
Milling, drilling, thread rolling
Milling, drilling and rolled threads for non-standard connections.
Forging and other changes
Cold or hot forging and other modifications according to the client's drawing.
Effect: A rod that fits the connection as designed - without adjustments on site.
High tensile threaded rods - strength classes, steels and coatings
The strength class, material and coating are set by the load and the working environment. We verify that the specified combination suits the application before production.
Class 4.8
For light structures and fixings.
Class 8.8
High tensile threaded rods and high tensile threaded bar for most structural and industrial connections, steel frames and anchoring.
Classes 10.9 and 12.9
For heavily loaded connections and load-bearing structures where the highest strength is required.
Stainless steel threaded rod A2 and A4
Stainless steel threaded rod and stainless steel studding for outdoor use (A2) and for moisture, salt or chemical exposure (A4). Stainless steel has lower strength than carbon steel class 8.8 - A2-70 and A4-70 reach 700 MPa against 800 MPa - so in load-bearing connections it is selected on the basis of the calculated forces.
42CrMo4 and 25CrMo4
Alloy steels such as 42CrMo4 and 25CrMo4 for threaded rods in pressure equipment and flanged joints.
Coatings
Zinc plated (Zn), hot-dip galvanized (HDG, tZn) or plain. Hot-dip galvanized threaded rods - in UK English, galvanised threaded rod or galvanised studding - are produced with the thread prepared for the coating and supplied with matching nuts - the thicker zinc layer means the thread tolerance has to be allowed for. More on this on the page about hot-dip galvanized fasteners.
Effect: A rod matched to its load and environment - checked before it is made.
Threaded rods and anchor rods for structures, masts and pressure equipment
Our threaded rods work wherever a connection has to carry a load for years - in foundations, steel structures and process installations.
Steel structures
Anchor rods and threaded rod anchors for anchoring steel structures and machinery in concrete foundations.
Poles, towers and masts
Foundation anchor rods and fixings for supporting structures in power transmission.
Pressure equipment
Threaded rods in 42CrMo4 and 25CrMo4 for flanged joints, supplied with the required documentation. PED fasteners
Industrial plants
Rods for mounting equipment and load-bearing connections in industrial installations.
Effect: One supplier of threaded rods for different parts of the same investment.
Threaded rods with nuts, washers and documentation for every batch
An incomplete delivery or missing documentation stops the assembly crew. We supply rods complete and documented.
Material certificates
EN 10204 3.1 inspection certificate for every batch.
Traceability
Batch traceability from the material to the finished rod.
Supplied as kits
Rods supplied with matching nuts and washers, in the quantities the assembly needs.
Effect: A complete delivery that can go straight to assembly.
Frequently asked questions
What is the difference between DIN 975 and DIN 976?
DIN 975 and DIN 976 describe the same fully threaded rod - DIN 975 has been withdrawn and replaced by DIN 976-1. Both designations are still widely used, so an order for a DIN 975 rod is fulfilled as a DIN 976-1 rod with the same dimensions.
Is threaded bar the same as threaded rod?
Yes, threaded bar and threaded rod are the same product - a rod threaded along its full length. In the UK it is also called studding or all thread; in technical documentation it is usually specified as DIN 976-1.
What strength class of threaded rod do I need?
The strength class of a threaded rod depends on the load: 4.8 for light fixings, 8.8 for most structural and industrial connections, 10.9 for heavily loaded connections and 12.9 for the highest loads. The class can be read from the marking: the first number × 100 gives the nominal tensile strength in MPa, and the product of both numbers × 10 gives the yield strength - for class 8.8 that is 800 MPa and 640 MPa.
What is the maximum size of a threaded rod?
Our threaded rods are made in diameters from M4 up to M80 and in lengths up to 6000 mm. Large sizes - such as an M27, M36 or M48 threaded rod - are made to order and cut to the length stated in the specification.
How much does a threaded rod cost?
The price of a threaded rod depends on the diameter, length, strength class or steel grade, coating and quantity. Send the size, class or material, coating and number of pieces - our sales team will reply with a price and lead time.
Which threaded rod is best for outdoor use?
For outdoor use, choose a hot-dip galvanized threaded rod (galvanised studding in the UK) or a stainless steel threaded rod in A2 or A4. A4 is the choice for salt, moisture or chemical exposure.
Can you make left-hand, imperial or trapezoidal threaded rods?
Yes, we make left hand threaded rods as well as threaded rods with imperial threads (UNC, UNF, BSW) and trapezoidal threaded rods. Please state the thread type, diameter and length in the inquiry.
How do I specify a threaded rod in an inquiry?
State the standard, thread size, length, strength class or material, coating and quantity - for example: DIN 976-1 M24 × 2000 - 8.8 - HDG, 200 pcs. Add the end form (form A or form B), the required certificate (EN 10204 3.1) and a drawing if the ends are machined.
What is the difference between DIN 976-1 form A and form B?
DIN 976-1 form A is a threaded rod with plain ends, typically supplied in stock lengths such as 1000 mm. Form B has chamfered ends and is usually supplied cut to the finished length as a stud. We make both forms and chamfer the ends in production when the specification requires it.
Is there an ISO equivalent of DIN 976?
There is no ISO standard that directly replaces DIN 976-1 for fully threaded rods, so DIN 976-1 - and the withdrawn DIN 975 - remain the reference across Europe. The thread is ISO metric, and the mechanical properties follow ISO 898-1 for carbon steel and ISO 3506-1 for stainless steel.
Do threaded rods come with material certificates?
Yes, every batch of threaded rods can be supplied with an EN 10204 3.1 inspection certificate. Rods for pressure equipment are supplied with the documentation required for the project.
Can threaded rods be supplied with nuts and washers?
Yes, threaded rods can be supplied as kits with matching nuts and washers. For hot-dip galvanized rods, the nuts are matched to the coated thread.
Elgo expert advice
When ordering threaded rods, specify the finished length, not the stock length. A rod ordered as a 3-metre bar and cut on site loses material, and every cut end needs deburring and - on coated rods - touching up.
A complete inquiry states the length, the end form (chamfer, undercut, machined end), the strength class or material, the coating and the required documentation. With that, rods arrive ready to install and the certificate matches exactly the batch on site.
If the connection is non-standard, send the drawing - we will check whether the rod can be made as designed before production starts.
Elgo - fastener manufacturer
Elgo is a European manufacturer and distributor of fasteners, with experience in the fastener industry going back to 1971. Our own machining shop in Poland lets us produce to drawing and supply complete, documented deliveries for industrial projects across Europe, including Central and Eastern Europe.
- PED fasteners for pressure equipment - stud bolts, nuts and washers in 25CrMo4, 42CrMo4 and 21CrMoV5-7, with EN 10204 3.1 / 3.2 certificates.
- Fasteners for steel structures - HV and SB bolting assemblies and anchor rods, including poles, towers and masts.
- Custom fasteners made to drawing - non-standard bolts, nuts and washers in small, medium and large series.
- Hot-dip galvanized fasteners - with the thread prepared for the coating and checked for assembly after galvanizing.
- DIN 976 threaded rods made to order - M4 to M80, up to 6000 mm, cut to length and machined to drawing.
One supplier takes responsibility for the material, the production, the coating and the documentation - so the client does not have to coordinate several companies. We also supply threaded rods in bulk to fastener distributors and wholesalers - priced individually for each order.
Send inquiry